Auto Car | Chevrolet Corvette C6 ZR1 | When it arrives next summer, the 2009 Chevrolet Corvette ZR1 will be the most powerful and fastest production car ever produced by General Motors, with performance enabled by a new, supercharged 6.2L LS9 small-block V-8 engine. Incorporating the engineering experience already found in the Corvette Z06's LS7 engine and the new-for-2008 6.2L LS3 of the Corvette, GM Powertain is targeting 100 horsepower per liter for the LS9, or 620 horsepower (462 kW), and approximately 595 lb.-ft. of torque (807 Nm); final SAE-certified power levels will be available in early March 2008. It is, indeed, the ultimate small-block engine for the ultimate Corvette.
The enabler of the LS9's performance is a new, large positive-displacement Roots-Type Supercharger - with a unique four-lobe design - developed for the engine by Eaton. It is teamed with an integrated charge cooling system that reduces inlet air temperature for maximum performance. The LS9 represents the first of several new, supercharged small-block engines that will be introduced in GM vehicles in the near future, each using Superchargers of similar design.
The enabler of the LS9's performance is a new, large positive-displacement Roots-Type Supercharger - with a unique four-lobe design - developed for the engine by Eaton. It is teamed with an integrated charge cooling system that reduces inlet air temperature for maximum performance. The LS9 represents the first of several new, supercharged small-block engines that will be introduced in GM vehicles in the near future, each using Superchargers of similar design.
More than just its tremendous peak horsepower and torque numbers, the supercharged LS9 makes big power at lower rpm and carries it in a wide arc to 6,600 rpm. GM Powertrain testing shows the engine makes approximately 300 horsepower (224 kW) at 3,000 rpm and nearly 320 lb.-ft. of torque (434 Nm) at only 1,000 rpm. Torque tops 585 lb.-ft. (793 Nm) at about the 4,000-rpm mark, while horsepower peaks at 6,500 rpm. The engine produces 90 percent of peak torque from 2,600 rpm to 6,000 rpm.
Heavy-duty and lightweight reciprocating components enable the engine's confident high-rpm performance, while the large-displacement Eaton Supercharger pushes enough air to help the engine maintain power through the upper levels of the rpm band. The LS9 is assembled by hand at GM's Performance Build Center, a unique, small-volume engine production facility in Wixom, Mich., that also builds the Corvette Z06's LS7 engine and other high-performance GM production engines.
The LS9's aluminium cylinder block features steel, six-bolt main bearing caps, with enlarged vent windows in the second and third bulkheads for enhanced bay to bay breathing. Cast iron cylinder liners - measuring 4.06 inches (103.25 mm) in bore diameter - are inserted in the aluminium block and they are finish-bored and honed with a deck plate installed. The deck plate simulates the pressure and minute dimensional variances applied to the block when the cylinder heads are installed, ensuring a higher degree of accuracy that promotes maximum cylinder head sealing, piston ring fit and overall engine performance.Nestled inside the cylinder block is a forged steel crankshaft that delivers the LS9's 3.62-inch (92 mm) stroke. It features a smaller-diameter ignition-triggering reluctor wheel and a nine-bolt flange - the outer face of the crankshaft on which the flywheel is mounted - that provides more clamping strength. Other non-supercharged 6.2L engines, such as the base Corvette's LS3, have a six-bolt flange. A torsional damper mounted to the front of the crankshaft features a keyway and friction washer, which also is designed to support the engine's high loads. Attached to the crankshaft is a set of titanium connecting rods and forged aluminium pistons, which, when combined with the cylinder heads, delivers a 9.1:1 compression ratio. This combination is extremely durable and lightweight, enabling the LS9's high-rpm capability.
The basic cylinder head design of the LS9 is similar to the L92-type head found on the LS3 V-8, but it is cast with a premium A356T6 alloy that is better at handling the heat generated by the supercharged engine - particularly in the bridge area of the cylinder head, between the intake and exhaust valves. In addition to the special aluminium alloy, each head is created with a rotocast method. Also known as spin casting, the process involves pouring the molten alloy into a rotating mold. This makes for more even distribution of the material and virtually eliminates porosity - air bubbles or pockets trapped in the casting - for a stronger finished product.
Although the heads are based on the L92 design, they feature swirl-inducing wings that are cast into the intake ports. This improves the mixture motion of the pressurized air/fuel charge. The charge enters the combustion chambers via titanium intake valves that measure 2.16 inches (55 mm) in diameter. Spent gases exit the chambers through 1.59-inch (40.4 mm) hollow stem sodium-filled exhaust valves. The titanium intake and sodium-filled exhaust valves are used for their lightweight and high-rpm capability. To ensure sealing of the pressurized engine, unique, four-layer steel head gaskets are used with the LS9's heads.
The broad power band enabled by the LS9's large-displacement Supercharger allows it to make strong low-end torque and great high-rpm horsepower, which allowed engineers to specify a camshaft with a relatively low lift of 0.555-inch (14.1 mm) for both the intake and exhaust valves. This low-overlap cam has lower lift and slower valve-closing speeds than the Z06's 505-horsepower (377 kW) LS7, helping the LS9 - with its approximately 620 horsepower - deliver exemplary idle and low-speed driving qualities. The camshaft actuates a valvetrain that includes many components, including the lifters, rocker arms and valve springs, of the LS3 engine. However, LS7 retainers are used to support the engine's high-rpm performance.
The LS9's R2300 Supercharger is a sixth-generation design from Eaton, with a case that is specific to the Corvette application. The Supercharger features a new four-lobe rotor design that promotes quieter and more efficient performance, while its large, 2.3-liter displacement ensures adequate air volume at high rpm to support the engine's high-horsepower aspiration. Maximum boost pressure is 10.5 psi (0.72 bar). The Supercharger is an engine-driven air pump that contains a pair of long rotors that are twisted somewhat like pretzel sticks. As they spin around each other, incoming air is squeezed between the rotors and pushed under pressure into the engine - forcing more air into the engine than it could draw under "natural" aspiration. The rotors are driven by a pulley and belt that are connected to the engine's accessory drive system.
The Corvette ZR1's LS9 engine is backed by a Tremec TR6060 six-speed manual transmission, with a twin-disc clutch system. It is based on the proven T56 six-speed, but upgraded to handle the LS9's torque output and delivers improved shift quality. The twin-disc clutch system provides exceptional clamping power, while maintaining an easy clutch effort. The system employs a pair of 260-mm discs, which spreads out the engine's torque load over a wider area, enabling tremendous clamping power to channel the LS9's torque. It also dissipates heat better and extends the clutch life (in normal driving).
Specification
Make: Chevrolet
Model: Corvette C6 Zr-1 Ls9 6.2 Supercharged
Year: 2009
Country of Origin: United States of America
Type: Supercar
Class: A
Engine: V8, Supercharger (Belt Driven Rootes Type Centrifugal), 6,187 CC, Gasoline
Horsepower: 638 BHP @ 6000 RPM
Tourque: 604 LB FT @ 4,200 RPM
Redline: 6,400 RPM
Brakes: Vented Steel Discs all Round, ABS
Wheels: 19 Inch Titanium alloy all round
Handedness: Left
Dials: Analouque main with Digital F1 style windscreen HUD
Readout: Both MPH
Transmission: 6 Speed H Pattern Manual
Driveline: F/R Front Engine, Rear Wheel Drive
0-60: 3.3 Seconds
Top Speed: 205 MPH
(www.ultimatecarpage.com)
No comments:
Post a Comment